Glass Laser Engraving and Etching Machines

Glass engraving

Glass Laser Engraving and Etching Machines

Frost names, logos and artwork onto wine glasses, bottles, mirrors and awards with an AEON Laser USA glass laser engraver. Make one gift or run a full batch.

Built by AEON and supported by AEON Laser USA, the manufacturer’s US team. 2-year warranty from the day your machine arrives.

Products

What you can engrave on glass

Laser engraving glass with a CO₂ laser leaves a permanent frosted mark in the surface. It does not cut glass. That frosted finish is what customers pay for on glassware, awards and gifts.

On a rotary attachment

Pint glasses and drinking glasses

Everyday glassware for bars, breweries, events and gifts.

On a rotary attachment

Wine glasses and stemware

Tapered shapes need to be leveled so the engraved area stays in focus.

On a rotary attachment

Bottles, growlers and decanters

Popular for weddings, corporate gifts and distillery merchandise.

Flat on the bed

Mirrors and flat glass panels

Engrave the back of a mirror to remove the coating and backlight the design.

Flat on the bed

Awards and plaques

Crystal holds heat and is harder to engrave cleanly, so test before taking an order.

Flat or on a rotary attachment

Jars, candle holders and ornaments

Low-cost blanks with strong seasonal demand.

Glass engraving design ideas

Illustrative images of the frosted look a laser gives glass.

  • Two wine glasses with a frosted laser-engraved floral wreath design
  • Glass bottle with a frosted laser-engraved botanical design
  • Mirror with a laser-engraved decorative border
  • Glass award with a frosted laser-engraved emblem
  • Glass jars and a candle holder with frosted laser-engraved patterns
How it works

How to laser engrave glass

Glass absorbs the CO₂ beam at its surface. The heat creates thousands of tiny fractures that scatter light, and the result is a crisp frosted mark in the surface of the glass.

People call this both laser engraving glass and laser etching glass. Traditional etching uses acid or sandblasting. A laser gives a similar frosted look with no chemicals, no stencils and no cleanup beyond a quick wipe.

1

Prepare the artwork

Set up the design in your laser software, such as LightBurn. Filled graphics and photos run as raster engraving. Outlines and single-line text run as vector engraving.

2

Position the piece

Flat glass sits on the bed. Round pieces mount on a rotary attachment, which turns the glass as the laser head scans.

3

Frame, then engrave

Frame the job to check placement, then run it. Wipe the piece clean and it is ready to hand over.

CO₂ laser

Bright, frosted engraving

Best for glassware, bottles, mirrors and awards, plus wood, acrylic and leather on the same machine.

UV laser

Very fine, smooth mark with minimal chipping

Best for small text, detailed logos and delicate or thin glass.

Machines

The right laser engraver for glass

Choose by the size of your glass pieces, how many you run at once and which other materials share the machine. Any glass engraving machine below can do the job. The difference is scale and detail.

MIRA 6X laser engraver for glass
X Series · 40 W RF CO₂

MIRA 6X

Fine detail on glassware and small glass gifts in a desktop footprint.

View the MIRA 6X
MIRA 9X laser engraver for glass
X Series · 75 W RF CO₂

MIRA 9X

A larger desktop working area for bigger pieces and mixed-material shops.

View the MIRA 9X
MIRA X glass engraving machine
X Series · 150 W RF CO₂

MIRA X

The largest working area in the MIRA X Series, for production runs and larger glass pieces.

View the MIRA X
PULSAR UV laser engraver and marker for glass
PULSAR Series · 10 W UV

PULSAR UV

The finest marks on glass, including small text and detailed logos.

View the PULSAR UV

ROTA2, ROTA4 and ROTA8 rotary attachments

Rotary attachments for the MIRA X Series that hold two, four or eight pieces at a time: ROTA2, ROTA4 and ROTA8. Ask a laser specialist which one fits your machine and your glassware.

Book a Laser Fit Call
Settings and tips

Settings and tips for clean glass engraving

Glass rewards a light touch. Too much heat chips the surface, so start gentle and build up with a material test.

The numbers below are starting points from AEON’s CO₂ support notes, not a recipe for every glass, laser source or lens.

Use lower power and higher speed

Glass needs far less energy than wood or acrylic. Start at 20 to 35% power and 300 to 400 mm/s, with power as low as possible.

Space the engraved lines out

Start at 200 to 250 LPI. Packing in more lines overlaps heat and roughens the mark.

Defocus slightly

Lowering the bed 1 to 2 mm spreads the beam and the heat. On tapered glasses, level the piece so the engraved area stays at one height.

Keep the surface cool

A thin layer of dish soap or a wet piece of newspaper over the engraving area spreads heat and cuts down on flaking.

Soften solid black artwork

Changing fills to about 80% black, or using dithering, gives a smoother frost.

Clean up after engraving

Wipe away loose glass with a damp cloth. Do not rub a bare finger over the mark.

Choose and test your glass

Composition varies by supplier, so run one piece before a full batch. Never engrave tempered or toughened glass, which can shatter.

FAQ

Glass engraving FAQ

Can you laser engrave glass?

Yes. A CO₂ laser engraves a permanent frosted mark into the surface of glass. A UV laser makes a finer, smoother mark for small text and detailed logos.

Can a laser cut glass?

No. The machines on this page engrave and mark glass. They do not cut it.

What is the difference between glass etching and glass engraving?

Traditional etching uses acid or sandblasting, and engraving uses a tool or a laser. With a laser, both words describe the same frosted result, which is why a laser is often sold as a glass etching machine.

What is the best glass etching machine for home or a small shop?

A desktop CO₂ laser such as the MIRA 6X handles glassware, wood, acrylic and leather in one machine. Plan for ventilation: the machine needs an exhaust path outdoors or a fume extractor.

What glass engraving equipment do I need besides the laser?

A rotary attachment for round pieces, exhaust ducting or a fume extractor, and laser software such as LightBurn for preparing designs.

Do I need a rotary attachment?

Only for round pieces such as wine glasses, pint glasses and bottles. Flat glass sits directly on the bed.

Can you laser engrave a mirror?

Yes. Engrave the back of the mirror to remove the reflective coating, which leaves a clear design you can light from behind. Test on a spare piece first.

Can I laser engrave tempered glass?

No. Do not engrave tempered or toughened glass. Surface damage can release its internal stress and make the piece shatter. Confirm the type of glass with your supplier first.

Will the engraving wash off?

The frosted mark is a change in the glass surface, not a coating, so there is nothing to peel. Before promising dishwasher safety, confirm the care conditions with your glass supplier.

Talk to a laser specialist

Not sure which machine fits your glass work?

A Laser Fit Call is a conversation with Steven, our resident laser pro. Tell him what you make and how many pieces you run. He will match you to a machine and rotary attachment.

Steven H.Your AEON Laser Pro

“Hi, I’m Steven. Whether you’re an individual maker just getting started or a shop running daily production, I’ve helped all kinds of users find the right machine. On your Laser Fit Call, I’ll learn what you make and match you to the exact model, power, and bed size for your goals and budget.”

Book Your Laser Fit Call

After you submit, you’ll be taken to Steven’s calendar to pick a time.