PULSAR UV Laser Engraver & Marker
UV Galvo Laser · 10 W, 355 nm
PULSAR UV Laser Engraver & Marker
A fully enclosed 10 W UV galvo laser for fine, high-contrast marking on plastics, glass and other heat-sensitive materials.
- 10 W JPT UV laser source at 355 nm
- 4.3 × 4.3 in marking area with a motorized Z axis
- Very small heat-affected zone for heat-sensitive materials
- Fully enclosed cabinet with an electric sensor door
- 2-YearUS-Based Warranty
- EnclosedElectric Sensor Door
- US Sales& Support
- 355 nmUV Wavelength
Finance Your PULSAR Through Geneva Capital
Apply in a few minutes and choose a term from 12 to 60 months.
PULSAR UV
Sharp marks on plastic and glass.
Very little heat.
The PULSAR UV is a fully enclosed 10 W UV galvo laser for fine, high-contrast marking on plastics, glass and other heat-sensitive materials. Its 355 nm JPT source marks with a very small heat-affected zone, and a motorized Z axis with red light pointers keeps setup quick.
Cold Marking For Heat-Sensitive Parts
The short 355 nm wavelength is absorbed at the surface of most materials, so the PULSAR UV marks with a very small heat-affected zone. That keeps edges clean on plastics, glass and coated parts that longer wavelengths can melt or discolor.
A Fine Beam For Small Detail
Pulses shorter than 20 ns and a beam quality of M² 1.25 or better focus the laser to a fine spot. Use it for small text, serial numbers, 2D codes and detailed logos where a clean, high-contrast mark matters.
Enclosed And Built For The Shop Floor
The enclosed cabinet keeps the beam behind an OD7+ CE certified laser safety window. An electric sensor door with anti-pinch protection opens the work area, an interior light shows the part, and a status light tower tells you from across the room when a job is running.
Fast Setup, Accurate Placement
Two red light pointers show you when the part is in focus, and the motorized Z axis moves the head up and down from the front panel. Fixture repeat jobs on the perforated worktable.
Technical Specifications
| Laser source | JPT UV, 10 W |
|---|---|
| Wavelength | 355 nm |
| Pulse width | Under 20 ns at 60 kHz |
| Frequency | 40 to 300 kHz |
| Beam quality | M² 1.25 or better |
| Marking area | 4.3 × 4.3 in (110 × 110 mm) |
| Scan head | Galvo, F-theta 163 lens |
| Focusing | Dual red light pointers |
| Z axis | Motorized |
| Enclosure | Enclosed cabinet, electric sensor door with anti-pinch protection |
| Viewing window | OD7+ CE certified laser safety window |
| Cooling | Water cooled, separate chiller |
| Software | EZCAD2 (Windows) |
| Power | 110 V or 220 V, 50/60 Hz, up to 500 W |
| Operating temperature | 32 to 104 °F (0 to 40 °C), non-condensing |
| Packed size and weight | Machine about 36.6 × 27.2 × 45.7 in, 298 lb. Chiller about 25.2 × 14.2 × 22.4 in, 53 lb |
What It Works On
Marks plastics, glass, rubber and wood, with fine surface marking on metals. Use it for logos, serial numbers, barcodes and QR codes, and fine detail on heat-sensitive parts.
Questions Buyers Ask
Should I choose UV or fiber?
A UV laser marks with far less heat, so it suits plastics, glass and other heat-sensitive materials. For deep engraving and color marking on metal, the PULSAR MOPA is the better fit.
How big is the marking area?
4.3 × 4.3 in (110 × 110 mm).
Does it need a chiller or special power?
The PULSAR UV is water cooled and uses a separate water chiller. It runs on 110 V or 220 V at 50/60 Hz and draws up to 500 W.
Is it enclosed?
Yes. The cabinet is fully enclosed, with an electric sensor door, anti-pinch protection and an OD7+ CE certified laser safety window.
What software does it use?
The PULSAR UV runs on EZCAD2, on Windows.
Backed by a 2-year US-based warranty and US sales and support.
Questions Before You Buy?
Talk To Our US Sales Team
Tell us what you mark and how many parts you run, and we will help you choose the right PULSAR for your shop.