How RF CO2 Lasers Stay Cool: Fans vs Water

Why Some RF Lasers Use Fans and Others Use Water

Most of AEON’s RF lasers are cooled with water, yet some RF lasers use only fans. In this episode of Tech with Lek, AEON’s Chief Technology Officer explains how each cooling method works, when each makes sense, and why temperature matters so much to an RF tube.

The short answer: Both methods can work well when the system is designed for them. Lek’s recommendation is water cooling for any RF tube above 40 watts, and if you have the choice of water cooling, take it. It helps the tube’s lifespan and keeps its power stable.

01

RF Describes the Source, Not the Cooling

RF stands for radio frequency. It tells you how the gas is excited to create the laser beam. It doesn’t tell you how the laser is cooled.

When a laser uses electricity, only part of that energy becomes the beam. Much of it becomes heat, and that heat has to go somewhere, just like the heat from your computer or your car’s engine.

Air cooling heat carried into room air RF source fins fan Water cooling RF source Chiller warm coolant cooled coolant
Two ways to move heat out of an RF source. Simplified drawing.
02

Air Cooling: Fins and Fans

With air cooling, heat moves into metal cooling fins and fans carry that heat away. That keeps things relatively simple, but airflow and room temperature matter.

Hot air or dusty cooling fins make the job harder, and over time they can cause premature failures.

03

Water Cooling: Coolant and a Chiller

With water cooling, coolant circulates through passages in the laser body, takes up the heat, and carries it to a chiller. Think of the coolant as a delivery truck for heat: it takes the heat away, gets cooled, then comes back for another load.

A properly sized, temperature-controlled chiller helps keep the source’s temperature steady during long jobs. Water cooling is useful when there is a lot of heat to remove, such as cutting and long periods of engraving.

04

Colder Isn’t Automatically Better

Coolant that’s too cold can cause condensation, just like a cold drink on a humid day. Always follow the manufacturer’s coolant and temperature guidance.

05

Choosing Cooling by Wattage

There isn’t one wattage where every laser tube suddenly has to switch to water. Different sources are engineered for different cooling methods. Lek’s recommendation is that any tube above 40 watts be water cooled.

Choose cooling that suits your source, your room, and your workload. Both methods can work well when the system is designed for them.

06

Why Temperature Matters So Much to an RF Tube

Cooling helps the laser maintain its performance. Water cooling alone doesn’t guarantee a better engraving, but it does help greatly with a tube’s lifespan and power stability.

  • Power: RF laser tubes are built at room temperature. As a rule of thumb from Lek, expect a 2 to 3% drop in output power for every 1°C increase, so the closer the tube stays to room temperature, the better.
  • Optics: RF tubes have internal optics that are difficult to cool.
  • Expansion: the tube itself is typically made of aluminum, which expands and contracts. Water cooling greatly reduces that expansion, which helps keep the optics in place and the gases inside where they belong.

Lek’s advice: if you have a choice of water cooling, choose that route.

07

Frequently Asked Questions

Does RF mean a laser is air cooled?

No. RF describes how the gas is excited to create the beam. An RF source can be cooled with fans or with water, depending on how it was engineered.

Is water cooling always better for engraving quality?

Water cooling alone doesn’t guarantee a better engraving. Its main benefits are a longer tube lifespan and more stable power.

At what wattage should an RF tube be water cooled?

There is no single cutoff, because sources are engineered for different cooling methods. Lek recommends water cooling for any tube above 40 watts.

Should I set my chiller as cold as possible?

No. Coolant that’s too cold can cause condensation. Use the manufacturer’s coolant and temperature guidance.

What makes air cooling less effective over time?

Hot room air and dusty cooling fins. Both make it harder for the fans to carry heat away and can lead to premature failures.

More From Tech with Lek

Each episode tackles one laser topic. Have a question for Lek? Leave it in the comments on the video.