Laser Acceleration Explained: G Ratings and Overscan

Same Top Speed, Different Finish Times

Two lasers can advertise the same top speed and still finish the same engraving at very different times. Acceleration is one reason why. In this episode of Tech with Lek, AEON’s Chief Technology Officer explains what a G rating measures, how it connects to overscan, and when a big number helps.

The short answer: A big G number is useful only when the machine can put it to work accurately. Look at acceleration alongside top speed, engraving quality, and the time to finish a real job.

01

Speed and Acceleration Are Different Measurements

Speed tells you how fast the laser head is moving. Acceleration tells you how quickly that speed changes.

Think of two cars with the same top speed but very different 0 to 60 times. On a short stretch of road, the one that gets up to speed sooner covers it first.

02

What a G Rating Means

Acceleration is sometimes advertised in G’s. 1G is about 9.8 m/s², a familiar unit based on Earth’s gravity. On a laser spec sheet it describes how quickly the head changes speed.

A 5G rating means five times that acceleration. It doesn’t mean the machine is five times faster, and it doesn’t mean every job finishes quicker.

03

A Simple Example: Getting to 1,000 mm/s

Say the head needs to reach 1,000 mm/s from rest. If acceleration were constant, at 1G it would take about 51 mm of travel. At 5G it would take about 10 mm.

Start, at rest 1G about 51 mm 5G about 10 mm same target speed, much less travel
Distance covered before the head reaches 1,000 mm/s, drawn to scale.

The target speed is the same, but the head covers much less distance getting there. Real controllers can ramp more gently, so these are simplified numbers. The relationship is the point.

04

Overscan: Where Acceleration Shows Up in Engraving

During engraving, the head travels back and forth and slows down at each end of the line. To do that without affecting the artwork, it usually travels past the edge of the design with the beam off. That extra travel is called overscan.

Overscan Artwork Overscan beam off beam on beam off
The head slows, reverses and gets back up to speed outside the artwork.

Higher usable acceleration can reduce the time and distance spent turning around. On a single pass the saving is small. On a narrow engraving with hundreds or thousands of scan lines, it can matter a lot, because the head spends a large share of the job turning around.

Lower acceleration artwork longer overscan longer overscan Higher usable acceleration artwork shorter overscan shorter overscan
One scan line across the same artwork. Illustrative, not to scale.
05

The Machine Still Has to Control the Movement

Acceleration is only useful if the machine can stay accurate while using it. Four things decide that:

  • Moving mass: how much weight the head and gantry carry
  • Belts: how well they hold position under load
  • Frame: how rigid the structure is
  • Motor tuning: how the drive system is set up

Push beyond what the system can handle and you can introduce vibration or positioning errors, which show up in the engraving.

06

How to Read a G Number When Comparing Lasers

Look at acceleration alongside top speed, engraving quality at that speed, and the time to finish a real job. A big G number is useful only when the machine can put it to work accurately.

For example, the MIRA X Series lists 8G acceleration alongside engraving speeds up to 3,000 mm/s. Use our laser comparison to see the specs side by side, and the demo checklist to time a real job.

07

Frequently Asked Questions

Does a 5G laser engrave five times faster than a 1G laser?

No. 5G means the head changes speed five times as quickly. It reaches the same top speed in less distance, which shortens turnarounds. It doesn’t raise the top speed itself.

What is overscan?

Overscan is the extra distance the head travels past the artwork, with the beam off, so it can slow down and reverse outside the engraved area.

Which jobs benefit most from high acceleration?

Narrow engravings with hundreds or thousands of scan lines, where turnaround time is a large part of the job.

Can acceleration be too high?

Yes. If it exceeds what the moving mass, belts, frame and motor tuning can control, the result can be vibration or positioning errors.

More From Tech with Lek

Each episode tackles one laser topic. Have a question for Lek? Leave it in the comments on the video.