How to Check Total Run Time and Machine Statistics: REDLINE MIRA S and NOVA S

Updated November 19, 2026

Applies to: REDLINE MIRA 5S, MIRA 7S and MIRA 9S, and REDLINE NOVA 10S, NOVA 14S and NOVA 16S

This guide shows how to see how long your laser has been switched on, how long it has spent running jobs and firing the laser, and how far it has traveled, using the keypad on the machine. It takes about a minute.

The controller in your laser keeps a running record of how much the machine has been used: how long it has been switched on, how long it has spent running jobs, how long the laser itself has fired, and how far the laser head and gantry have traveled. You can read these values, along with the version of the controller’s mainboard, on the System data screen. They help you plan maintenance, and our support team may ask for them when you open a ticket.

Nothing is changed: These steps only show information. They do not change any setting on your machine.

Check your menu first: The keypad menu is not the same on every firmware and HMI version. The screens in this guide are from firmware RDC-V14.37.16 with HMI-V10.10.10.26. If your menu has no System data> item, do not follow these steps. Find your versions with our guide How to Find the Firmware and HMI Version: REDLINE MIRA S and NOVA S, then open a support ticket with both numbers, and our technicians will point you to the right screen.

What you need

  • No tools: everything is done on the keypad of your laser
  • The laser switched on and idle, with no job running or paused
  • About one minute

Read this guide all the way through before you start. The steps follow the way our own technicians check these values.

Get to know the control panel

Everything in this guide is done on the control panel: the screen, and the keypad to the right of it. You only need the five keys highlighted in the diagram. The photos show a REDLINE MIRA. The REDLINE NOVA has the same control panel.

Control panel of a REDLINE MIRA, with the screen on the left and the keypad on the right
The control panel on a REDLINE MIRA: the screen, with the keypad to its right.
Keypad diagram with the Menu, X right arrow, Y down arrow, Enter and Esc keys highlighted
The keypad. The keys used in this guide are highlighted in red.
Key What it does in this guide
Menu Opens the menu. It is the round key in the middle of the arrow keys.
X→ (right arrow) Moves the highlight across to the right column.
Y↓ (down arrow) Moves the highlight down one item.
Enter Opens the highlighted item.
Esc Goes back one screen.

1. Open the System data screen

  1. With the laser switched on and idle, press Menu. A menu opens with two columns of items, and the first item in the left column, Laser Set>, is highlighted.

    Caution: Leave the other items in this menu alone unless a technician asks you to use them. Several of them change how your machine is set up.

    Menu on the controller screen with System data outlined in red
    The menu as it opens. System data>, outlined in red, is the fourth item in the right column.
  2. Press X→ (right arrow) once to move the highlight to the right column, then press Y↓ (down arrow) three times. System data> is the fourth item in the right column. If a different item is highlighted there, press Esc to close the menu and go back to the note at the top of this guide.

    System data highlighted in the menu on the controller screen
    System data> is highlighted. Press Enter to open it.
  3. Press Enter. The System data screen opens, and the values fill in after a moment.

2. Read the values

The screen lists eight values. Times are shown as hours, minutes and seconds (h:m:s), and distances in meters (m). You do not need to press anything: the values are read as soon as the screen opens. Leave the Read mainboard info button at the bottom as it is.

System data screen listing run times, travel distances and the mainboard version
The System data screen. Here the Total on time of 00018:06:00 means 18 hours and 6 minutes.
On the screen What it tells you
Total on time How long the machine has been switched on, in total.
Total processing time How long the machine has spent running jobs, in total.
Previous process time How long the most recent job took.
Total laser on time How long the laser beam has been on, in total.
Total process times How many jobs the machine has run.
X Cumul.Travel How far the laser head has traveled from side to side, in meters.
Y Cumul.Travel How far the gantry has traveled from front to back, in meters.
Mainboard version The firmware version of the controller. Our technicians may ask for it.

Total processing time is the value to use for maintenance. The cleaning intervals in our guides Recommended Maintenance: REDLINE MIRA S and Recommended Maintenance: REDLINE NOVA S are given in work hours.

3. Go back to the main screen

  1. Press Esc. The menu returns.

  2. Press Esc again. The main screen returns.

Note: Stop when the main screen is showing. If you press Esc again while the laser is idle, the laser head moves back to its origin point.

You can now check how much your laser has been used at any time. If the System data screen does not open, or a value looks wrong, open a support ticket and tell us what you see. A photo of the screen helps our technicians help you faster.

Need a hand?

Email support@aeonlaser.us or call 321-260-2325. More ways to reach us are on the Support page.

← Back to the Knowledge Base