How to Clear the Controller Memory: REDLINE MIRA S and NOVA S

Updated November 19, 2026

Applies to: REDLINE MIRA 5S, MIRA 7S and MIRA 9S, and REDLINE NOVA 10S, NOVA 14S and NOVA 16S

This guide shows how to delete every job file stored on your laser’s controller, using the keypad on the machine. It takes about a minute.

Job files that you send to your laser, or copy to it from a USB drive, are saved in the controller’s memory. Over time they build up: the file list gets long, and the controller can run out of room for new jobs. Clearing the memory removes them all at once. Only job files are deleted; the settings of your machine are not changed.

Warning: This cannot be undone. These steps permanently delete every job file stored on the controller. The design files saved on your computer are not affected, so make sure you still have the original of anything you will want to run again.

This guide is for REDLINE machines. If you have a legacy MIRA or NOVA, the keypad is different: follow How to Clear the Controller Memory: MIRA and NOVA (Legacy) instead.

What you need

  • No tools: everything is done on the keypad of your laser
  • The laser switched on and idle, with no job running or paused
  • About one minute

Read this guide all the way through before you start. The steps follow the way our own technicians clear the memory.

Get to know the control panel

Everything in this guide is done on the control panel: the screen, and the keypad to the right of it. You only need the six keys highlighted in the diagram. The photos show a REDLINE MIRA. The REDLINE NOVA has the same control panel.

Control panel of a REDLINE MIRA, with the screen on the left and the keypad on the right
The control panel on a REDLINE MIRA: the screen, with the keypad to its right.
Keypad diagram with the Shift, Frame, X right arrow, Y down arrow, Enter and Esc keys highlighted
The keypad. The keys used in this guide are highlighted in red.
Key What it does in this guide
Shift Held down while you press Frame. It is in the right column of keys, third from the top.
Frame Pressed while Shift is held down, it opens the file screen. It is directly above Shift.
X→ (right arrow) Moves the highlight across to the column of commands.
Y↓ (down arrow) Moves the highlight down one item.
Enter Carries out the highlighted command.
Esc Clears a message, or goes back one screen.

1. Open the file screen

  1. With the laser switched on and idle, look at the main screen. Under Combination key menu it lists what the keys do while Shift is held down. The second line, frame = File, is the one this guide uses.

    Key combinations listed on the main screen, with frame = File outlined in red
    The key combinations on the main screen. Shift with Frame, outlined in red, opens the file screen.
  2. Hold down Shift and press Frame, then let go of both keys. The file screen opens: the job files in the controller’s memory are listed on the left, with a column of commands on the right. A preview of the highlighted file is drawn at the top left of the screen.

    File screen with the job files listed on the left and a column of commands on the right
    The file screen: the job files on the left, the commands on the right.

2. Delete all files

  1. Press X→ (right arrow) once. The highlight moves to the column of commands, onto the first one, Worktime prev.

  2. Press Y↓ (down arrow) five times, until Del all file, the sixth command, is highlighted.

    Del all file highlighted in the column of commands and outlined in red
    Del all file, outlined in red, is the sixth command. Highlight it, then press Enter.

    Caution: Only Del all file is needed. Leave the other commands alone unless a technician asks you to use them. In particular, do not select Format mem, at the bottom of the column: it formats the controller’s memory.

  3. Press Enter. Every file is deleted straight away, with no second prompt. Delete Successful appears at the top left of the screen, with Please <Esc> below it. The files are still listed for the moment: the list clears in the next step.

    Top of the screen showing Delete Successful and Please Esc, outlined in red
    Delete Successful, at the top left of the screen, confirms that the files have been deleted.

3. Check that the memory is clear

  1. Press Esc once. The message clears, and the file list is now empty.

    File screen with an empty file list
    The file list is empty once the memory has been cleared.
  2. Press Esc again to return to the main screen.

Note: Stop when the main screen is showing. If you press Esc again while the laser is idle, the laser head moves back to its origin point.

The controller’s memory is now clear and ready for new jobs. If files are still listed after you follow these steps, or the laser shows an error message, open a support ticket and tell us what you see. A photo of the screen helps our technicians help you faster.

Need a hand?

Email support@aeonlaser.us or call 321-260-2325. More ways to reach us are on the Support page.

← Back to the Knowledge Base