How to Find the Firmware and HMI Version: REDLINE MIRA S and NOVA S

Updated November 19, 2026

Applies to: REDLINE MIRA 5S, MIRA 7S and MIRA 9S, and REDLINE NOVA 10S, NOVA 14S and NOVA 16S

This guide shows how to read the firmware version and the HMI version of your laser from its screen as the machine starts up. It takes about a minute.

Your laser shows both version numbers on its screen every time it starts up. They tell our support team exactly which software your machine is running, and the menus on the keypad are not the same on every version, so we may ask you for them when you open a ticket.

Have a legacy MIRA or NOVA? Its screen shows the versions in a different place. Use our guide How to Find the Firmware and HMI Version: MIRA and NOVA (Legacy) instead.

What the two versions are: The firmware is the software on the controller, the board that runs your laser. The HMI (human-machine interface) is the control panel: the screen and its keypad. Each has its own version number.

What you need

  • No tools: everything is read from the screen of your laser
  • The laser switched off to begin with: the versions show only as it starts up
  • A phone to photograph the screen: optional, but it makes the numbers easy to read back
  • About one minute

Read this guide all the way through before you start. The steps follow the way our own technicians check the versions.

1. Start up the laser

  1. If the laser is on, make sure no job is running or paused, then switch it off. Wait a few seconds.

  2. Check the work area, then switch the laser on.

    Caution: The laser head moves to its home position as the machine starts up. Before you switch the laser on, make sure nothing inside the cabinet is in its way.

  3. Watch the top left corner of the screen. The screen lights up and shows the AEON Laser logo. A few seconds later the main screen appears, with three lines of text in its top left corner.

    Control panel of a REDLINE MIRA as it starts up, with three lines of text in the top left corner of the screen outlined in red
    The control panel as the laser starts up. The three lines, outlined in red, are in the top left corner of the screen.

2. Read the two versions

The second and third lines are the two version numbers. The numbers on your machine may be different from the ones shown here. They stay on the screen only while the laser is starting up, so read them straight away.

Top of the screen during startup, with the firmware version and the HMI version outlined in red
The top of the screen, closer. The second and third lines, outlined in red, are the firmware version and the HMI version.
On the screen What it tells you
X/Y Resetting. . . The laser is starting up and moving the laser head to its home position.
RDC-V14.37.16 The firmware version of the controller.
HMI-V10.10.10.26 The HMI version: the version of the screen and keypad.
Cancel please <Esc> Shown a little lower down. Pressing Esc now would cancel the reset, so leave the keypad alone.
  1. Write down the RDC line and the HMI line exactly as they appear, or take a photo of the screen with your phone. If you miss them, switch the laser off, wait a few seconds and switch it on again: they show every time the laser starts up.

  2. Let the laser finish starting up. Do not press any keys until the laser head has stopped moving and the lines have cleared from the screen.

You can also read the firmware version at any time, without restarting the laser: it is the Mainboard version on the System data screen. See our guide How to Check Total Run Time and Machine Statistics: REDLINE MIRA S and NOVA S.

You now have the firmware and HMI version of your laser. Include both when you open a support ticket. If the lines do not show on your machine, or you cannot read them, send us a photo or a short video of the screen as the laser starts up. It helps our technicians help you faster.

Need a hand?

Email support@aeonlaser.us or call 321-260-2325. More ways to reach us are on the Support page.

← Back to the Knowledge Base