Knowledge Base
All Guides
Guides, videos and manuals for your AEON laser.
Removing the Internal Chiller: MIRA 9
Remove the internal chiller from a MIRA 9 before turning the machine on its side.
Read Guide →Removing the Fan: MIRA 7
Remove the exhaust fan from a MIRA 7: mounting bolts, hose, capacitor ties, wiring and ground.
Read Guide →Removing the Fan: MIRA 9
Remove the exhaust fan from a MIRA 9: hose, mounting bolts, wiring and ground.
Read Guide →Cleaning the Laser Head and Optics: MIRA
Clean the autofocus sensor, lens, nose cone, mirrors and camera on a MIRA, and replace the lens or Mirror 3 when needed.
Read Guide →Winterizing Your Laser
Protect a water cooled laser from freezing: when to act, how much antifreeze to use, and the steps for storage or continued use.
Read Guide →Recommended Maintenance: NOVA
The maintenance schedule for a NOVA 10, 14 or 16, with steps for the optics, camera, exhaust, bed and chiller.
Read Guide →Recommended Maintenance: MIRA
The maintenance schedule for a MIRA 5, 7 or 9, with steps for the optics, camera, exhaust, bed and chiller.
Read Guide →Recommended Maintenance: REDLINE NOVA S
The maintenance schedule for a REDLINE NOVA S, with steps for the optics, camera, exhaust, bed, chiller, linear rail and air co...
Read Guide →Recommended Maintenance: REDLINE MIRA S
The maintenance schedule for a REDLINE MIRA S, with steps for the optics, camera, exhaust, bed, chiller and linear rail.
Read Guide →Removing the Internal Chiller: REDLINE MIRA 7S
Step-by-step removal of the internal chiller from a REDLINE MIRA 7S.
Read Guide →Removing the Internal Chiller: REDLINE MIRA 9S
Step-by-step removal of the internal chiller from a REDLINE MIRA 9S.
Read Guide →Steps Per Rotation: Roller Rotary
Fix rotary engravings that come out stretched or squished by measuring a test square and recalculating steps per rotation.
Read Guide →Common Machine Errors and Solutions
What slop errors, Hard Limit Protect, Machine Protected, Water Error 1 and file transfer failures mean, and how to clear each o...
Read Guide →Alignment Process: REDLINE Series
Align the mirrors of a single tube REDLINE MIRA S or NOVA S with Near and Far shots, then verify with a 5 Point Test.
Read Guide →Replace a Driver: MIRA
Swap a motor driver in a MIRA 7 or MIRA 9: unplug the terminal blocks, change the driver and plug them back in.
Read Guide →Replace the 24V Power Supply: MIRA
Replace the 24V power supply in a MIRA and set the new unit to 115V before fitting it.
Read Guide →Replace the 40V Power Supply: MIRA
Replace the 40V power supply in a MIRA, which sits behind the 24V supply, and set the new unit to 115V.
Read Guide →Replacing the Auto Focus Pin
Swap a bent or sticking auto focus pin on a MIRA, and check that the sensor light comes on afterwards.
Read Guide →Smart Rotary: MIRA Pro
Set up the Smart Rotary on a MIRA Pro: choose the wheel setup, load the rotary settings, align and focus, run the job and retur...
Read Guide →External Air Compressor
Why an external air compressor helps with cutting, how the smart solenoid switches air sources, and how to set up a California ...
Read Guide →Install a 4” Lens: NOVA
Fit the 4” lens to a NOVA for thicker materials and deeper items, then calibrate the auto focus with a focal ramp test.
Read Guide →Install a 2.5” Lens: MIRA
Swap the standard 2” lens in a MIRA for a 2.5” lens and focus it manually, for more clearance on tall objects.
Read Guide →Install a 1.5” Lens: MIRA
Swap the standard 2” lens in a MIRA for a 1.5” lens, for finer engraving detail.
Read Guide →Wireless Remote Control for AEON Lasers
What each button on the wireless remote does, and how to wire a remote into a legacy or REDLINE machine.
Read Guide →CO2 Laser Tubes: RF or Glass?
How RF and DC glass CO2 laser tubes differ in cost, durability, performance and maintenance.
Read Guide →Solenoid Retrofit: MIRA 9
Fit the new solenoid valve body to a MIRA 9 and reconnect its three air lines.
Read Guide →Chiller Flow Sensor Replacement
Replace a failed chiller flow sensor: remove the old one, fit the new one the right way round and join the wires with solder se...
Read Guide →Roller and Chuck Rotary Guide: REDLINE MIRA S
Install and use a roller or chuck rotary on a REDLINE MIRA S: set up the rotary, configure LightBurn, prepare the file and run ...
Read Guide →Drive Belt Replacement: MIRA and NOVA
Replace the X or Y drive belt on a MIRA or NOVA, check the tension, then tune the scanning offset settings in LightBurn.
Read Guide →Smart Rotary: NOVA
How to set up, align and run the Smart Rotary on a NOVA, and how to return the machine to flat settings afterwards.
Read Guide →Optics Kit Guide: Available Lenses and Installation (REDLINE NOVA S)
The lens options for a REDLINE NOVA S, what is in the optics kit, and how to install and focus each lens.
Read Guide →Optics Kit Guide: Available Lenses and Installation (REDLINE MIRA S)
The lens options for a REDLINE MIRA S, what is in the optics kit, and how to install and focus each lens.
Read Guide →4 Inch Lens Kit MIRA
Swap the standard lens on a MIRA for the 4 inch lens kit, then set focus manually with the focus gauge.
Read Guide →Focal Lenses: Types and Applications
How focal length and lens diameter affect your results, and which AEON lens fits which machine.
Read Guide →How to maintain the chiller of AEONLaser
Overview In this guide, you will learn how to perform proper maintenance on the MIRA S chiller. Frequency of water change Every...
Read Guide →The Use of Remote Control on AEONLaser
Overview What you will learn In this guide, you will learn how to handle a remote control on your AEONLaser, allowing you to op...
Read Guide →Leveling Knife Blade Table on your NOVA Redline
Overview What you will learn You will learn to level the working platform on NOVA Redline. Why do this? Having a horizontal pl...
Read Guide →Still Stuck? Call (321) 260-2325
Our US-based support team is one phone call away. More ways to reach us are on the Support page.