Knowledge Base

All Guides

Guides, videos and manuals for your AEON laser.

MIRA S seriesNOVA Redline

How to Change the Screen Language: REDLINE MIRA S and NOVA S

Change the language on the screen of a REDLINE MIRA or NOVA, for example back to English, from the keypad.

Read Guide →
MIRA LegacyNOVA Legacy

How to Find the Firmware and HMI Version: MIRA and NOVA (Legacy)

Read the firmware version and the HMI version of a legacy MIRA or NOVA from its screen as the laser starts up.

Read Guide →
MIRA S seriesNOVA Redline

How to Clear the Controller Memory: REDLINE MIRA S and NOVA S

Delete every job file stored on the controller of a REDLINE MIRA or NOVA from the keypad, to make room for new jobs.

Read Guide →
MIRA S seriesNOVA Redline

How to Find the Firmware and HMI Version: REDLINE MIRA S and NOVA S

Read the firmware and HMI version of a REDLINE MIRA or NOVA from its screen as the machine starts up.

Read Guide →
MaintenanceMIRA S series

How to Check Total Run Time and Machine Statistics: REDLINE MIRA S and NOVA S

See how long a REDLINE MIRA or NOVA has been switched on, running jobs and firing its laser, on the System data screen of the k...

Read Guide →
MIRA LegacyNOVA Legacy

How to Change the Screen Language Back to English: MIRA and NOVA (Legacy)

Switch the screen on a legacy MIRA or NOVA back to English from the keypad, even if you cannot read the language it is showing.

Read Guide →
MIRA LegacyNOVA Legacy

How to Clear the Controller Memory: MIRA and NOVA (Legacy)

Delete every job file stored on the controller of a legacy MIRA or NOVA from the keypad, in about a minute.

Read Guide →
Getting StartedNOVA Redline

Getting Started with REDLINE NOVA

Prepare your workspace, then receive, uncrate, roll off the pallet, set up and power on a REDLINE NOVA for the first time.

Read Guide →
Getting StartedMIRA S series

Getting Started with REDLINE MIRA 7S and MIRA 9S

Prepare your workspace, then receive, uncrate, set up and power on a REDLINE MIRA 7S or MIRA 9S for the first time.

Read Guide →
Getting StartedMIRA S series

Getting Started with REDLINE MIRA 5S

Prepare your workspace, then receive, unpack, set up and power on a REDLINE MIRA 5S for the first time.

Read Guide →
Getting StartedMIRA S series

What’s in the Box: REDLINE MIRA S and NOVA S

The standard contents that ship with a REDLINE MIRA S or NOVA S, with a photo of each item.

Read Guide →
All machinesGetting Started

Prepare Your Workspace

Electrical, ventilation, safety and temperature requirements to set up before your laser arrives.

Read Guide →
All machinesGetting Started

Laser Delivery

Inspect the crate when your laser arrives, and report any damage without refusing the shipment.

Read Guide →
Getting StartedNOVA Legacy

Unboxing and Setting Up Your NOVA

Video walkthroughs for uncrating a NOVA, setting it up, checking the alignment and running a first engrave.

Read Guide →
Getting StartedMIRA Legacy

Lifting, Turning or Moving Your MIRA

Prepare a MIRA 7 or MIRA 9 for tight spaces, then tip it safely onto its side on a furniture dolly.

Read Guide →
Getting StartedMIRA Legacy

Lifting Your MIRA onto a Stand or Workbench

How four people lift a MIRA safely onto its stand or a workbench, then level it.

Read Guide →
Getting StartedMIRA Legacy

Unboxing and Setting Up Your MIRA Pro

Uncrate a MIRA Pro, lift it onto its stand, unpack it, fill the chiller, vent the fan and power it on for the first time.

Read Guide →
Getting StartedMIRA Legacy

Unboxing and Setting Up Your MIRA

Uncrate a MIRA, lift it onto its stand, unpack it, fill the chiller, vent the fan and power it on for the first time.

Read Guide →
All machinesGetting Started

Machine Shipping and Receiving: What to Expect

What to tell us before delivery, how tracking and scheduling work, and what to check when your machine arrives.

Read Guide →
Getting StartedNOVA Legacy

Disassembly and Reassembly: NOVA

Take a NOVA 10, 14 or 16 apart into its top and base, move it through tight spaces, then reassemble and rewire it.

Read Guide →
Getting StartedNOVA Redline

Disassembly and Reassembly: REDLINE NOVA S

Take a REDLINE NOVA apart into its top and base, move it through tight spaces, then reassemble and reconnect it.

Read Guide →
AccessoriesAll machines

LightBurn Camera Setup

Calibrate the LightBurn camera on a MIRA or NOVA, use it to place and trace designs, and fix common placement issues.

Read Guide →
AccessoriesLightBurn

LightBurn Bridge Setup: MIRA

Connect a LightBurn Bridge to your MIRA, join it to your Wi-Fi network and add it as a device in LightBurn.

Read Guide →
All machinesLightBurn

LightBurn Basics

A tour of LightBurn: design tools, vector and raster graphics, the workspace and its windows, and how to run a project.

Read Guide →
All machinesLightBurn

LightBurn Setup: After Your Machine Arrives (Mac)

Install LightBurn on a Mac with your license key, load the device profile from the USB drive and connect to your laser by USB o...

Read Guide →
All machinesLightBurn

LightBurn Setup: After Your Machine Arrives (PC)

Install LightBurn on Windows with your license key, load the device profile from the USB drive and connect to your laser by USB...

Read Guide →
All machinesLightBurn

LightBurn Setup with a License Key: Before Your Machine Arrives (Mac)

Install LightBurn on a Mac, activate your license key and create your machine as a device before your laser arrives.

Read Guide →
All machinesLightBurn

LightBurn Setup with the Free Trial: Before Your Machine Arrives (Mac)

Install the LightBurn free trial on a Mac and create your machine as a device before your laser arrives.

Read Guide →
All machinesLightBurn

LightBurn Setup with a License Key: Before Your Machine Arrives (PC)

Install LightBurn on Windows, activate your license key and create your machine as a device before your laser arrives.

Read Guide →
All machinesLightBurn

LightBurn Setup with the Free Trial: Before Your Machine Arrives (PC)

Install the LightBurn free trial on Windows and create your machine as a device before your laser arrives.

Read Guide →
MaterialsMIRA S series

Optimizing Air Assist to Improve Engraving Detail and Cutting Efficiency (REDLINE)

How the air assist controls work on a REDLINE MIRA S or NOVA S, and when to use low or high air pressure.

Read Guide →
All machinesMaterials

Optimizing Score Line Settings

How to balance speed, power and focus for clean, consistent score lines on a CO2 laser.

Read Guide →
All machinesMaterials

Understanding Materials and Settings for a CO2 Laser

The fundamentals of choosing materials and finding speed, power, LPI and focus settings for a CO2 laser.

Read Guide →
All machinesMaterials

Engraving Raster Images

How to choose, edit and set up a photo for raster engraving in LightBurn.

Read Guide →
All machinesMaterials

Optimizing Tumbler Settings

The speed, focal depth and LPI tests we use to find the best settings for engraving a tumbler.

Read Guide →
All machinesMaterials

How to Configure a Full Wrap Design When Engraving Tumblers

How to measure a tumbler and size a LightBurn file so a design wraps the full circumference.

Read Guide →
All machinesMaterials

Material Rapid Test

How to use the Material Rapid Test file to find engraving and cutting settings for any material.

Read Guide →
All machinesMaterials

Optimizing Acrylic Settings

Suggested speed and power ranges for etching, engraving, scoring and cutting acrylic.

Read Guide →
All machinesMaterials

Glass Engraving

Starting settings and tips for engraving glass without cracking it.

Read Guide →
MIRA LegacyTroubleshooting

Move the Y-Sensor Bracket

Adjust or replace the Y-Sensor when the gantry hits the back of the laser on homing, or after a camera collision.

Read Guide →
MIRA LegacyTroubleshooting

Squaring the Laser Head: MIRA

Check a MIRA laser head against a 90 degree square after a crash, and adjust it until it sits square.

Read Guide →
All machinesTroubleshooting

Why Is My CO2 Laser Not Cutting?

Ten things to check when your CO2 laser will not cut through: settings, optics, squareness, alignment, focus, air, chiller wate...

Read Guide →
MIRA LegacyTroubleshooting

Aligning Mirrors on Your MIRA

A four-part video series on mirror alignment for the MIRA: beam logic, then Mirror 1, Mirror 2 and Mirror 3.

Read Guide →
MIRA LegacyTroubleshooting

Bed Will Not Raise

What to check when the bed of your MIRA only goes down: restart, the sensor light and the auto focus pin.

Read Guide →
MIRA LegacyTroubleshooting

5 Point Test: MIRA

Pulse into tape at five points on a MIRA bed to check the beam is centered in the nozzle, and adjust Mirror 3 if it is not.

Read Guide →
NOVA LegacyTroubleshooting

5 Point Test: NOVA

Pulse into tape at five points on a NOVA bed to check the beam is centered in the nozzle, and adjust Mirror 3 if it is not.

Read Guide →
MIRA LegacyTroubleshooting

How to Manage an Auto Focus Crash: MIRA

The checks to run, in order, after the laser head crashes into the bed or material during auto focus on a MIRA.

Read Guide →
MaintenanceMIRA Legacy

Removing the Internal Chiller: MIRA 7

Remove the internal chiller from a MIRA 7 before turning the machine on its side.

Read Guide →

Still Stuck? Call (321) 260-2325

Our US-based support team is one phone call away. More ways to reach us are on the Support page.

Open a Support Ticket